A thick glass door may be a decorative door with any thickness of 12 mm or higher. It is generally composed of two parts: the movable fan and the fixed glass. The door frame is divided into steel, copper and aluminum alloy. 1 Before the engineering is completed, check whether the elevation in the ground and the height from the structure at the top with the door frame meet the theory requirements. Determine the position with the door frame and tips on how to install the glass. Choose the glass based on the design requirements. Finished profile door frame, confine groove, plate and tumbler glue, floor spring, timber screw, self-tapping screw and other auxiliary materials.
2 Installation points associated with fixed door frame thicker fire resistant glass supplier (1) Release and positioning According to the design requirements, the position of the door frame is published, and the fixed and also movable part installation command lines are determined.
(2) The width on the stainless steel limit groove limit groove on the top of the installation door frame should be greater than the glass thickness of 2~4mm, plus the groove depth is 10~20mm.
(3) Install the metal veneer on the floor first, then glue the s / s panel to the wood side. The aluminum alloy square tube is often fixed on the mode column with an light weight aluminum corner code, or is usually fixed on the embedded embedded component by screws.
(4) Slice glass (usually pre-cut, then tempered and transported to the site for installation). The dimensions from the bottom, middle and top from the actual volume should often be measured, and the cut size with the minimum size of the glass width needs to be selected. If the dimensions measured while in the upper, middle and lower will be the same, the size is actually cut, the width is a lot less than the measured size of Two to three mm, and the height is less than Less than six mm. For the slice glass, the chamfered edging will be carried out on your four sides by hand-held oil-coated rock, with a chamfer wider of 2 mm.
(5) Install the glass with a glass suction cup for you to lift the thick glass up, insert the thick glass plate in the limit groove at the most notable of the door mode, and then place it to the bottom bracket so how the edge of the heavy glass plate just seals the side. The stainless steel trim belonging to the frame column faces this seam.
(6) The glass is fixed within the bottom bracket and that pressure clamp strip is actually installed, about 4mm from the the thick glass eating plan. Then apply the universal glue about the strip and stick the stainless plate on the remove.
(7) Inject the glass seal for the top limit groove plus the bottom support, and inject the glass glue on the joint between the thick glass and the frame column, so that this glass glue forms a uniform straight line for the gap. Finally, scrape from the excess glass glue along with wipe the glue having a clean cloth. When thicker glass is butted, the joint needs to be kept at a mileage of 2~3mm. The thick glass edge ought to be chamfered. After the two thick glass sit and fixed, the glass glue can be used to inject into this gap. After filling, the actual thick glass is loaded. Squeeze the glass glue upon both sides and wipe the glue which has a clean cloth.
3 The installation point of the movable door leaf thick glass The thick cup movable door leaf features no door frame. The opening and closing on the movable door leaf is realized by the hardware hinged to the upper and lower rails on the frame.
(1) Floor spring mounting ground spring is usually an automatic door closing unit installed under various home fans.
(2) Mark top of the and lower rails belonging to the door leaf, and fix the pin hole plate of the rotation pin and the rotation shaft connection plate from the floor spring by the actual wire. Refer to the installation instructions mounted on the ground spring product for installation.
(3) Drill the holes in the door handle (usually instructed to be processed when buying thick glass). Note the height dimension of the actual thick glass should are the mounting portion that is inserted in the upper and lower bed rails. Usually the cut sizing of thick glass really should be less than about 5mm involving measurement size for realignment.
(4) Install the higher and lower rails about the upper and lower sides from the thick glass door and measure the height in the door. If the upper and lower edges in the door leaf are not likely the specified value while in the gap between the door frame plus the ground, the wooden splint is usually placed under the glass in the upper and lower bed rails. If the door leaf levels exceeds the installation size, the excess portion with the thick glass door leaf needs to be cut.
(5) After establishing the height, fix the upper and lower rails. In the gap between the thick glass and the metal upper and decrease rails, a small wooden strip is inserted while doing so, and then the cup glue is injected on the gap between the compact wooden strip, the thick glass as well as the crosspiece.
(6) Door enthusiast positioning installation. First, adjust the positioning pin within the door frame beam featuring a own adjustment screw towards beam plane 1~2mm. Next erect the glass door leaf, align the hole position on the rotating pin connector in the lower crosspiece of the door leaf with the rotation pin of your spring, and turn the door leaf to fit the hole into that pin. Then, with the pin axis for the reason that axis, turn the entrance leaf 90° (to correct the door leaf any time turning), so that the door leaf along with the door beam are from right angles. At now, the hole of your rotating connecting piece in the crosspiece of the door leaf is usually aligned on the door frame beam. The positioning pin is ended up and the positioning pin is proved, and inserted into the hole in the door leaf cross-rotating pin connecting member is all about 15 mm. Install the glass door handle. Previous to installation, apply a little glass glue to the part the location where the handle is inserted in the glass. When the tackle is assembled, the root is closely mounted on the glass, and then the repairing screw is tightened to ensure the handle is not necessarily loose.